This is how my workbench typically looks. Most of my fellow modelers are much more tidy and organized. But out of chaos comes order. The kitchen renovations finished last month, which freed me up to work on my layout again. I finally got around to wiring up my DC power switching box. I actually got to use my soldering station and volt meter for the first time. My soldering skills were somewhat lacking at the beginning, but they got better near the end. Here's the final product. All the parts were purchased from Digi-Key. I'd definitely recommend them to anyone. Friendly service, great selection and reasonable shipping/brokerage fees.
I finally got to test my interchange module. Here's a video of the first run using my new power switch. I'm pretty happy with the results.
During setup, I discovered why Kato sells separate packages of rail joiners. As I was connecting and re-connecting track, the metal piece broke off a few of the rail joiners. You can see the missing metal piece in the track situated on the right side in the picture. Fortunately, I had purchased extra rail joiners and was able to replace them. The blue plastic is used to remove the joiner from the track.
The reason for connecting and re-connecting the unitrack was that I had finished my platform for the city overhead station. The construction of this platform went fairly quick. However, I made it too long and consequently both ends of the platform were too close to the S curves. I had forgotten about clearance so when I ran my train through the station for the first time, it was rubbing against the corners of the platform. Boy did I feel dumb! So I had to shorten the platform and moved the S curves further away from the platform. A mitre box and hacksaw certainly came in handy for this, but it wasn't pretty.
Unfortunately, not all of my modeling is as successful as my platform doh! I also worked on the bridge module. I wanted to construct a contemporary looking arch for the bridge. I decided to use styrene tubes that I thought I could bend. The Evergreen styrene tubes only came in lengths of 24" so I extended them by placing an insert inside to connect two 24" lengths together. I thought that if I had a long enough insert I could bend the tube without fear of breaking. I remembered my platform arches had become brittle after applying solvent to them, but I thought I could avoid this problem with more plastic to reinforce the structure. How wrong I was. I applied some weight at the centre of the tube and used a hair dryer to warm up the styrene. As soon as the styrene became warm, it broke exactly at the spot where the solvent was applied. So it's back to the drawing board for the bridge.
What with having to shorten the platform because I forgot about clearance and the shattered remnants of a bridge gone wrong, I was feeling pretty miserable. So I thought some retail therapy might cheer me up and picked up the Minitrix LINT train set. Despite some setbacks this month, I'm pretty happy with the progress I've made and I gained more knowledge about modeling. Hopefully this renewed interest in trains will continue through to December. Now if only I could figure out what to do about that damn bridge.
I finally got to test my interchange module. Here's a video of the first run using my new power switch. I'm pretty happy with the results.
During setup, I discovered why Kato sells separate packages of rail joiners. As I was connecting and re-connecting track, the metal piece broke off a few of the rail joiners. You can see the missing metal piece in the track situated on the right side in the picture. Fortunately, I had purchased extra rail joiners and was able to replace them. The blue plastic is used to remove the joiner from the track.
The reason for connecting and re-connecting the unitrack was that I had finished my platform for the city overhead station. The construction of this platform went fairly quick. However, I made it too long and consequently both ends of the platform were too close to the S curves. I had forgotten about clearance so when I ran my train through the station for the first time, it was rubbing against the corners of the platform. Boy did I feel dumb! So I had to shorten the platform and moved the S curves further away from the platform. A mitre box and hacksaw certainly came in handy for this, but it wasn't pretty.
Unfortunately, not all of my modeling is as successful as my platform doh! I also worked on the bridge module. I wanted to construct a contemporary looking arch for the bridge. I decided to use styrene tubes that I thought I could bend. The Evergreen styrene tubes only came in lengths of 24" so I extended them by placing an insert inside to connect two 24" lengths together. I thought that if I had a long enough insert I could bend the tube without fear of breaking. I remembered my platform arches had become brittle after applying solvent to them, but I thought I could avoid this problem with more plastic to reinforce the structure. How wrong I was. I applied some weight at the centre of the tube and used a hair dryer to warm up the styrene. As soon as the styrene became warm, it broke exactly at the spot where the solvent was applied. So it's back to the drawing board for the bridge.
What with having to shorten the platform because I forgot about clearance and the shattered remnants of a bridge gone wrong, I was feeling pretty miserable. So I thought some retail therapy might cheer me up and picked up the Minitrix LINT train set. Despite some setbacks this month, I'm pretty happy with the progress I've made and I gained more knowledge about modeling. Hopefully this renewed interest in trains will continue through to December. Now if only I could figure out what to do about that damn bridge.
5 comments:
Great to see you back working on your layout! Sorry to hear about your setbacks...nothing can be more discouraging than to have that feeling of all the time and money 'wasted' on something that won't work right...I've been there! Persistence and tenacity are necessary 'character building' traits one will develop with this hobby! The video made your work look really good, and your home made platforms are still an inspiration for me (I hope to get around to creating my own this month).
One more thing...my workbench only looks more organized when I'm not working on anything and I've cleaned it for photographs! Most times it looks more like yours (including the same clamps from Home Depot!).
Hi Jerry,
Thanks for the encouraging words. Despite the setback with the bridge, I view it as a positive experience as it adds to my modelling knowledge. I'll definitely know not to do that again!
Alvin
Hang in there. If it all goes to plan you're just unambitious! Since I wasn't hatched out of an egg knowing how to do this stuff I've had to stumble along through painful and expensive trial and error, but it makes the successes that much more rewarding, or so I choose to tell myself!
I've love to hear your impressions of the LINT. I've been eyeing it too- it does not really fit my layout but that's never stopped me before.
Hi Jaggy. My apologies for not replying back to you. I usually get an e-mail notice when someone leaves a comment, but not this time.
In regards to your question, I wouldn't recommend the Trix LINT. At least the low end version. I've been having some problems with it running on my unitrack. The unit is really light weight so contact with the track is not very good and it doesn't seem to run smoothly.
Post a Comment